• FrSky TFR8SB FASST Compatible S.Bus 8 to 16 Channel Receiver

    Click image to enlarge
    - FrSky TFR8SB FASST Compatible S.Bus 8 to 16 Channel Receiver Out of stock
    £38.40 (Incl. VAT)
    Qty

    No Longer available

     

    FASST 2.4GHz Air Systems (7CH Mode/Multi Mode): 6EX 7C TM-7 TM-8 T8FG T10C TM-10 T10CG T12Z T12FG TM-14 T14MZ etc.

    1.1.2  Compatible servos at SB port

    Futaba S.BUS servos FrSky S Bus compatible servos D12MB

    Model: TFR8SB (8CH FASST compatible receiver with RSSI & SB ports)

    Dimension: 44.5*27.5*17mm

    Weight: 11.5g

    Operating Voltage Range: 3.5~10V

    Operating Temperature Range: -10℃~80℃

    Servo Frame Rate: 14ms (FS – Normal Speed Mode)

                       7ms (HS – High Speed Mode)

     

    Note: Be sure that when using battery or regulated output from ESC the capacity must meet the usage conditions of servos.

    1.3 Features

    1) Compatible with FASST 2.4GHz Air Systems (7CH Mode/Multi Mode)

    2) SB port is compatible with Futaba S.BUS servos and FrSky S Bus compatible servos

    3) With RSSI output

    4) Two selectable failsafe setting options (use native failsafe on radio side or set failsafe on TFR8SB side)

    5)S.BUS servos/S Bus compatible servos channel setting channel setting on TFR8SB

    6)Improve sensitivity and stability

    7)Wider and higher operating temperature range suitable for all kinds of models

    8)Firmware upgradeable

     

    2.  Set Up

    2.1 Bind procedure

    Turn on the transmitter connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is

    off and GREEN LED is solid the binding process is completed and the receiver is operating normally.

    2.2 Setting failsafe

    TFR8SB support two selectable failsafe setting options either use native failsafe position preset on the transmitter side

    or set failsafe on TFR8SB.

    2.2.1 Use native failsafe position preset on the transmitter side:

    If not disabling failsafe on the transmitter side TFR8SB will use native failsafe position preset on the transmitter side.

    2.2.2 Set failsafe on TFR8SB side:

    TFR8SB supports failsafe function for all channels. Follow the steps below to set failsafe on TFR8SB:

    1) Bind the receiver first and disable failsafe on the transmitter side;

    2) Set all transmitter controls to the desired failsafe position;

    3) Press briefly the F/S button of the receiver the GREEN LED of the receiver will flash twice indicating the failsafe is

    set up successfully.

    I f you do not need the failsafe function any more just re-bind the receiver to set default failsafe mode.

    2.3LED status

     

    RED LED

    GREEN LED

    Mode

    Off

    On

    Normal mode

    On

    On

    Waiting to be bound

    Flashing

    On

    Signal lost

    On

    Flashing twice

    Set failsafe

    Flashing slowly

    On

    Normal speed mode

    Flashing fast

    On

    High speed mode

     

     

    3.  How to switch between two PPM modes

    Turn the transmitter off connect the battery to the receiver press the F/S button of receiver for 6 seconds and then release. The red LED will flash fast in HS Mode and slow in FS Mode. Repeat this to alternate modes.

     

    Note: HS mode is only applied for high-speed digital servos. Other servos should select FS mode otherwise servos will get hot or even burn out.

     

    4.  Channel Setting Methods

    Channel setting for Futaba S.BUS servos and FrSky S Bus compatible servos can be performed at TFR8SB.

    1 Connect the SB port and RSSI port by the provided cable.

    2 Connect an S.BUS servo or S Bus compatible servo to the output connector (1~8) corresponding to the channel you want to set.

     

    Output Connector

    Channel Setting

    Mode A

    Mode B

    1

    1

    9

    2

    2

    10

    3

    3

    11

    4

    4

    12

    5

    5

    13

    6

    6

    14

    7

    7

    15

    8

    8

    16

     

    3 Connect battery to the receiver RED blinking LED indicating the channel setting is completed in Mode A. To switch to Mode B press the button on receiver for three seconds until GREEN LED starts to blink indicating the channel setting is completed in Mode B.

    Mode A: RED LED blinks

    Mode B: GREEN LED blinks

     

    Note: Do not perform linking procedure while motor’s main wire is connected or engine is operating otherwise damage may occur. After linking is completed recycle the receiver power and check if the receiver is really under control by linked transmitter.